![]() ![]() For the NuVinci H3 controller (right handlebar side), configure:.Proceed to configure the controller, depending on the controller your e-bike has:.Systems with 4.X.X firmware will only show one variant of System Configuration.Chain only or belt compatible - make sure to select this variant on firmware variants 3.X.X.Bosch geared - make sure to select this only for Bosch Gen 2 variants.Rear cog size - number of teeth on the rear sprocket.Front cog size - number of teeth on the front sprocket.Enter the bicycle configuration, and configure the hub interface:.NuVinci ARC Advanced Rider Controller (a grip controller used in the left side of the handlebar).NuVinci H3 controller (a 3-button controller used in the right side of the handlebar).A NuVinci controller, one of two choices:.4 - Configure the hub interface and controller Tools You will find more information on this in the system configuration section. To ensure you have the proper parameters available please save the parameters prior to the update. Alternatively, to exit the configuration already:Īfter each firmware update, a new calibration is necessary and the parameter settings need to be updated.Proceed below to configure the hub interface and controller.If the update fails, please reconnect the USB cable, restart the Desktop software, and repeat the process up to here.After the firmware update is run and a confirmation appears, select “OK” to return to the main screen.Select the firmware process, which will be opened automatically, according to the process you need:.To use or edit an old configuration, select “Load setup from file”.To flash a new software version, select “Update firmware”.Choose what configuration you need to do for your AHI system, from one of two options:.With the software open on your computer and connected to the hub interface, select “enviolo Automatic setup”.You will see the screen “Communications established”, and from there, you will be able to choose multiple configuration options.ģ - Flash the firmware to the hub interface Tools.Select “Click to connect” on the computer.Connect the computer and enviolo AHI via a Mini-USB cable. ![]() Open enviolo Automatic and Harmony desktop software 3.0 version.Pull the cable, located as shown below.Disconnect the hub interface main cable from the e-bike.A bicycle with an Automatic, Automatic , Harmony, or Harmony H|sync hub interface.A computer with an installation of the Automatic and Harmony Desktop Software 3.0 version.Install and follow the instructions, and complete the installation.Ģ - Establish a connection between the computer and the hub interface Tools.Download the desktop software from the link provided above.You can find the files on “C:\Program Files (x86)\FallbrookTechnologies directory”.Before installing, make sure to delete any files from a previous installation of the Automatic and Harmony Desktop Software.A new installation of the Automatic and Harmony desktop software 3.0 version.If you had a previous installation of the Automatic and Harmony desktop software, make sure to delete the old files before a new installation. On windows, you can find them on “C:\Program Files (x86)\FallbrookTechnologies directory”.A computer with Windows 7, Windows 8 or Windows 10:.Step-by-step instructions 1 - Download and install the software Tools Note that the desktop Automatic and Harmony software is not a necessary component for troubleshooting, and should be used only for firmware upload and configuring the hub interface. You may need this guide in some situations, such as after replacing the hub interface, or to change the gear ratio configuration on the e-bike. When you upgrade to a newer model Harmony, you can transfer the configuration from your old remote to your new remote.This article will help you to install and update the Harmony and Automatic system with desktop software. Testing your remote settings after a software upgrade This testing process is the same as the one you did when you set up your Harmony One for the first time. Remove your Harmony from the charging station.Ĭonnect your Harmony to your computer using the USB cable.Īfter you finish making any changes to your Harmony One’s configuration, you should test the new set up to ensure everything is working the way you expect. However, sometimes you may need to update the firmware manually. Generally, when you connect your remote to your computer the Harmony Remote Software updates your remote automatically if new firmware is available. Logitech updates the firmware for your remote to ensure you’re always getting the most from your Harmony One. The remote’s firmware is similar to your computer’s operating system. Your Harmony One contains internal software, called firmware. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |